USDT TRC-20 transfer fee calculator
A TRC-20 USDT transfer burns 6.43 TRX if you pay in TRX (13.03 TRX to a brand-new address). Enter your case below — the chain parameters are pulled live, not hardcoded.
Your transfer
Energy is bought in packages and does not carry over, so the count rounds up.
Chain parameter: getEnergyFee = 100 SUN per energy (page default; JS tries to fetch the live value)
What it costs
- Energy needed
- 64,285
- Burn TRXenergy × getEnergyFee
- 6.43 TRX
- Rent energy1 package × 65,000
- 1.37 TRX
- You save
- 5.06 TRX
Math: 64,285 × 100 ÷ 10⁶ = 6.4285 TRX. Rental estimated at 1.365 TRX per package.
Buy energy — delivered on paymentNo signup · No spending approval · No private key
Bandwidth not included: a standard TRC-20 transfer is about 345 bytes, the first 600 bytes per day are free, and beyond that TRX burns atgetTransactionFee = 1000 SUN per byte (roughly 0.35 TRX per transfer). Sending to a never-activated address adds a one-time activation fee of getCreateNewAccountFeeInSystemContract = 1.00 TRX.
Where these numbers come from
This is not an estimate — it is chain parameters multiplied out. TRON charges contract calls in energy, and energy has a governance-set price, getEnergyFee (currently 100 SUN, or 0.0001 TRX per unit). So:
burn cost = energy consumed × getEnergyFee ÷ 10⁶
64,285 × 100 ÷ 10⁶ = 6.43 TRX
Renting works differently: the energy already exists because someone else staked TRX for it, so you pay a rental rate rather than the full burn price. That is why 65,000 energy costs 6.43 TRX to burn but a little over one TRX to rent.
Verify it yourself in three steps
- Read the chain parameter:
POST https://api.trongrid.io/wallet/getchainparameters, findgetEnergyFee. - Simulate the transfer with
wallet/triggerconstantcontract; theenergy_usedfield is what this specific transfer consumes. - Multiply the two and divide by 10⁶. Compare against any quote you are given.
When you should just burn TRX
- You transfer a handful of times a month. The time spent comparing beats the savings.
- You already stake a lot of TRX. You may already have more energy than you use.
- You need to move funds right now. Burning TRX requires no setup at all.
Frequently asked
Are these chain parameters live?
The page fetches getEnergyFee from TronGrid when it loads and shows the query time underneath. If the request fails it falls back to the built-in default (100 SUN per energy) and says so explicitly — it never presents a stale default as live data.
Why does sending to a new address cost twice as much?
A TRC-20 transfer to an address that has never held USDT requires the contract to create a new balance entry, which costs roughly 66,000 extra energy. Addresses that already hold USDT skip that write. Sending to a never-activated address also incurs a one-time activation fee of 1 TRX (chain parameter getCreateNewAccountFeeInSystemContract).
Why does my actual fee differ from this estimate?
Three common reasons: the recipient address is in an unusual state (blacklisted, or its balance was just cleared); the chain parameters changed between your query and your transaction; or the transaction also consumed bandwidth beyond the free 600 bytes per day, adding about 0.35 TRX. The transaction receipt is the only authoritative number.
If I buy energy, do I still burn TRX?
Not for computation, as long as the energy covers the transfer. Bandwidth is separate: the first 600 bytes per day are free, and beyond that TRX is burned at getTransactionFee per byte. A standard TRC-20 transfer is about 345 bytes, so the first one or two transfers each day usually cost nothing extra.
How much energy should I buy at once?
For a single transfer to an address that already holds USDT, 65,000 energy is enough (actual usage is about 64,285). A new address needs about 130,285, so two packages. Energy does not carry over — it returns to the delegator at expiry — so buy for the transfers you are actually making.